- 您现在的位置：买卖IC网 > Sheet目录370 > ZXLD1362ET5TA (Diodes Inc)IC LED DRIVR WHITE BCKLGT TSOT-5
A Product Line of
Diodes Incorporated
ZXLD1362
Application Information (cont.)
Thermal Considerations
device to be mounted on a 25mm PCB with 1oz copper
When operating the device at high ambient temperatures, or
when driving maximum load current, care must be taken to
avoid exceeding the package power dissipation limits. The
graph below gives details for power derating. This assumes the
2
standing in still air.
1100
1000
900
800
700
600
500
400
300
200
100
0
-50 -30 -10 10 30 50 70 90 110 130 150
AMBIENT TEMPERATURE (°C)
Maximum Power Dissipation
Note that the device power dissipation will most often be a
maximum at minimum supply voltage. It will also increase if the
efficiency of the circuit is low. This may result from the use of
unsuitable coils, or excessive parasitic output capacitance on
the switch output.
Thermal Compensation of Output Current
High luminance LEDs often need to be supplied with a
temperature compensated current in order to maintain stable
and reliable operation at all drive levels. The LEDs are usually
mounted remotely from the device so, for this reason, the
temperature coefficients of the internal circuits for the
ZXLD1362 have been optimized to minimize the change in
output current when no compensation is employed. If output
current compensation is required, it is possible to use an
external temperature sensing network - normally using
Negative Temperature Coefficient (NTC) thermistors and/or
diodes, mounted very close to the LED(s). The output of the
sensing network can be used to drive the ADJ pin in order to
reduce output current with increasing temperature.
Layout Considerations
LX Pin
The LX pin of the device is a fast switching node, so PCB
tracks should be kept as short as possible. To minimize ground
'bounce', the ground pin of the device should be soldered
directly to the ground plane.
Coil and Decoupling Capacitors and Current Sense
Resistor
It is particularly important to mount the coil and the input
decoupling capacitor as close to the device pins as possible to
minimize parasitic resistance and inductance, which will
degrade efficiency. It is also important to minimize any track
resistance in series with current sense resistor R S . Its best to
connect V IN directly to one end of R S and I SENSE directly to the
opposite end of R S with no other currents flowing in these
tracks. It is important that the cathode current of the Schottky
diode does not flow in a track between R S and V IN as this may
give an apparent higher measure of current than is actual
because of track resistance.
ZXLD1362
Document number: DS33472 Rev. 5 - 2
21 of 24
www.diodes.com
May 2012
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ZXLD1366DACTC
IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1370EST16TC
IC LED DRVR HIGH BRIGHT TSSOP-16
ZXLD1371QESTTC
IC LED DRIVER
ZXLD1374EST20TC
IC LED DVR BUCK BOOST 20TSSOP
ZXLD1937ET5TA
IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD381FHTA
IC LED DRIVR WHITE BCKLT SOT23-3
ZXLD383ET5TA
IC LED DRIVR WHITE BCKLGT TSOT-5
ZXSC300E5TA
IC LED DRVR WHITE BCKLGT SOT23-5
相关代理商/技术参数
ZXLD1362ET5TA-CUT TAPE
制造商:DIODES 功能描述:ZXLD1362 Series 1 A 1 MHz SMT LED Driver with Internal Switch - TSOT-23-5
ZXLD1366
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:High accuracy 1A, 60V LED driver with internal switch
ZXLD1366_10
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:HIGH ACCURACY 1A, 60V LED DRIVER WITH INTERNAL SWITCH
ZXLD1366DACTC
功能描述:LED照明驱动器 1A, 60V LED Drver, Int Swtch RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
ZXLD1366DACTC-CUT TAPE
制造商:DIODES 功能描述:ZXLD1366 Series 1A 500 kHz High Accuracy LED Driver with Internal Switch - DFN-6
ZXLD1366EN8TC
功能描述:电流和电力监控器、调节器 LED DRVR W/ INT SW 1A 60V RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
ZXLD1366ET5TA
功能描述:LED照明驱动器 1A, 60V LED Drver, Int Swtch RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
ZXLD1370
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:60V HIGH ACCURACY BUCK/BOOST/BUCK-BOOST LED DRIVER CONTROLLER